Zahl HM1

A/B comparison

CConcerning the reference quality of the HM1, the idea of using it for critical A/B comparisons is most obvious - be it for evaluating different sources like D/A converters or cartridge systems in the high-end range or comparing different mixes or sound processing options in the professional range.

For this purpose, the HM1 has two inputs with independent level control and on/off buttons. Exact level matching is essential for a critical A/B listening comparison. By the way, the on/off function can also be operated via a cable remote control, which facilitates a blind comparison.

Cross-fade

The mixing stage can also be used to crossfade two sources. A very musical alternative to the otherwise usual "hard" switching.

Mixing two sources

And of course this stage is suitable for mixing any two sources. A new programme is created from two music programmes. This new programme can then not only be listened to in the headphones but is also available at the line outputs on the back of the unit, which can be used for connecting active speakers and recording units. This turns the HM1 into a 2-channel stereo mixing console with reference quality.

Also important: If only one channel is used, the mixing stage is not superfluous "ballast". An unused channel is switched off directly at the input stage and thus cannot negatively influence the signal integrity. This switch-off is realised via relays and is triggered as soon as a volume control is set to minimum or a channel on/off button is in the off position.

This stage is not designed to massively affect the sound. As a rule, all audio gear connected to the HM1 is of extremely high quality, a classic tone control would not be appropriate.

However, it can be advantageous to make fine, precise adjustments in the frequency response domain, depending on the headphones, music programme or even personal preference.

Low and high frequency adjustment

The low and high frequency adjustment, each in three fixed steps as boost and cut, is primarily designed for musical purposes. We have further developed proven circuits from studio technology to achieve a stage which sets subtle accents rather than changes the sound character. The basis are filters with selected components, of course all circuits are precisely switched by relays.

Professionals use the functionality, for example, to find out whether a mix is balanced in terms of low and high frequencies or can still be optimised.

Stereo Base control, a little theory

A special feature is the possibility to adjust the stereo width. The perception of spatiality when listening with headphones differs from listening with loudspeakers. Instead of a cross-feed circuit, we use our stereo base width setting. It is based on the mid/side technique which is commonly used in professional studios. It provides additional benefits.

The stereo signal is converted into a mid signal (in simple terms, what L and R have in common) and a side signal (in simple terms, what distinguishes L and R). Summing mid and side signals in a 1:1 ratio will result in the original stereo signal. However, if you change the ratio between mid and side before summing them, you change the stereo base width. In our circuit, we leave the mid signal as it is. We only adjust the level of the side signal. If we lower the level, the stereo image becomes narrower, if we raise the level, the stereo image becomes wider.

Stereo Base control, what it does

You have direct access to the perception of spatiality. With a music programme which seems too "wide" in the headphones, one will turn the control one or two steps to the left. If you perceive a recording as too "dry" (centred), turn the control one or two steps to the right. The leftmost position is mono. This is the preferred setting for early stereo recordings, when individual instruments have been mixed to the extreme left or right - without spatial reference.

Professional users check the spatiality of their mix with this function and may discover possible problems, especially in the extreme positions.

Also important: With the DIR (Direct) button, this stage can be completely switched out of the signal path. In this way, the purist approach is taken into account.

A precision potentiometer with 21 detents is available for balance control. The centre position is perfectly calibrated and haptically clearly defined. In fine increments, left/right volume differences of up to about 2.5 dB - caused by music programme, headphones or individual perception - can be compensated.

XLR 4-pin connector and ¼ inch jack socket are wired in parallel and are intended for alternative use. Theoretically, you could use both at the same time, the power amplifier is strong enough. However, for a reference quality listening experience, we do not recommend such use.

Ideally, the XLR 4-pin is used in conjunction with balanced wired headphones. In this case, the signal currents of the two power amplifiers are not mixed with each other, mutual interference is impossible. The HM1 can unfold its full quality (also refer to chapter "Dual Mono Design").

Dual Mono vs. Balanced amplifier design

With its dual mono design, the HM1 features the same advantages as a balanced output stage but avoids the drawbacks.

The drawbacks of a balanced output stage are the significantly increased number of electronic components - a balanced output contains two output stages per channel which work in reverse phase. Two output stages result in doubling the output impedance. More components result in an increased risk of non-linearities.

¼ inch jack compatible

Another advantage of the HM1 architecture is that unbalanced headphones with ¼ inch jack plugs can also be operated without any problems.

Balanced signals (XLR) or unbalanced signals (RCA) can be connected to Line Input A and Line Input B. XLR and RCA must not be used simultaneously on the same input. The Bal/Unbal switches set the inputs independently to balanced (Bal) or unbalanced (Unbal) mode.

Each input provides another switch which adds an extra 15dB gain. This ensures that even signals with low levels can be processed without any problems.

The signal at the line outputs corresponds to the signal in the headphones, except that it does not pass through the headphones amplifier, but through balanced or unbalanced line output stages and is routed to connectors on the rear.

Connect active speakers, power amps or other gear

Balanced and unbalanced outputs may be used simultaneously to drive power amplifiers, active speakers, level meters or other components. If, for example, the HM1 is used for comparing two stereo sources, the result may be recorded using one of the outputs. The same applies when using the HM1 as a mixing console.

The "A Thru" signal is tapped from Input channel A, post input amplifier. The switchable 15dB gain stage at Input A affects the “Thru” signal. The Thru output has an unbalanced output stage.

Setup your own test bench / experimental bench

A signal connected to Input A can thus be routed to another application without loss. Application example: "A Thru" is routed to a sound processing device or effects unit, the output of this unit is fed to Line Input B. The ratio between original and processed signal can be set by the A/B volume controls. Of course, this setup is also excellent for testing any device: Channel A supplies the original, channel B the signal coming from the unit to be tested.

The idea

The idea behind strictly separating left and right channels is to keep any interference away from the circuits. A term like “crosstalk” does not get to the core of the matter. Music signals usually have left/right references, so that an extremely low crosstalk value - moreover, usually measured with sine waves - does not mean so much. But with music highly energetic signal pulses occur, and then high currents are individually demanded by the output stages. It is extremely important that in these cases there is no coupling via a common power supply or via ground lines carrying signal current. Only this way an amplifier can produce absolutely undistorted output signals.

Realisation inside the HM1

In the HM1, the power supplies for left and right channels are separate, for preamplifiers and power amplifiers. The mains transformer has independent, completely potential-separated windings for each channel. Rectification, filtering and voltage regulation for each channel are individual. For logic circuitry and front-panel indicators, there is another winding and separate rectification, filtering and voltage regulation.

The ground potentials of the two channels are connected to each other at one point only, but this is done purely as potential equalisation; it is impossible for signal currents to be mixed.

Optimal output connection

If the XLR 4-pin output is used in combination with balanced wired headphones, the dual mono principle is implemented in full consequence.

When using the jack output, the ground wires of both channels are connected in the jack socket and the jack plug of the headphones. The use of headphones with jack plugs therefore is not that ideal. In the HM1, however, an optimised ground routing ensures that the disadvantageous effects are as low as possible.

(also refer to chapter: Headphones Outputs / Balanced Connection)

Mains voltage and mains transformer are always potential sources of interference - consequently, we have outsourced them to the HMP1 mains adapter.

The mains adapter also contains a standby power supply unit which delivers a stabilised low voltage. This voltage is applied to the Power switch on the front panel of the HM1 and serves to switch on the actual mains transformer via a relay.

Worldwide operation

The standby power supply has a wide-range input, is a purely linear design and complies with the common standby power regulations.

The mains input is equipped with one of the best interference filters available and can be set for operation on the following voltages: 100V-110V-120V-220V-230V-240V.

The mains switch on the back of the HMP1 can be used to completely de-energise the unit.

Variable cable length

The connecting cable between the mains adapter and the main unit carries potential-separated low voltages only. The length of the cable is variable over a wide range and can be defined by the user when ordering.

Power Supply

Mains Voltage – AC 50-60Hz, switchable 100V / 110V / 120V / 220V / 230V / 240V
Power Consumption – typ. 40W, max. 60W

Measures and Weights

HM1: WxHxD approx. 225 x 90 x 300mm, approx. 5kg
HMP1 (Mains Adapter): WxHxC approx. 170 x 60 x 185mm, approx. 1,2kg